Sunday, December 29, 2019
Easa Module 7 - 5155 Words
m7 Module 7 Essay Questions 1) Describe how tooling is controlled in a part 145 maintenance organisation. Introduction Tool control within a part 145 maintenance organisation can be divided in two main areas, the control of company supplied tools and the individual control of their own personal tooling. Tool control is a part 145 requirement Safety Good tool control is essential to prevent any tooling from becoming a foreign object which might cause an obstruction, restriction or any other type of damage. Tools should be checked before use for serviceability and operators should be trained to use them to prevent damage to the aircraft and personnel. The whereabouts of all personal and company†¦show more content†¦The area affected could be as vital as a main wing spar or as simple as an access panel. I would then determine the type of corrosion. There are many types of corrosion which could be as severe as intergranular corrosion or as simple as surface corrosion. I would then determine the severity of the damage by taking both of the above factors into account before making my decision to either repair, replace and just simply leaving it alone. Besides those 2 important factors, i would also take into accounts things like time constraints, spares availability and manpower constraints. With that said my final de cision would depend on the procedures laid down in the aircraft maintenance manual(AMM) and structural repair manual(SRM). Safety Ensure that there is adequate manpower who are properly trained to perform the job. Ensure that all the people working around the area is aware of the job being carried out. Personnel should be wearing any personal protective equipment like mask, goggles, gloves, etc that is required by the particular job. If the task deals with any chemicals or even the corrosion itself, extra precautions should be observed. Leaving it alone If after performing my inspection and with reference to the applicable manuals, i determine that the corrosion is minor and does not require any further work, i would remove the corrosion using theShow MoreRelatedEasa Module 75162 Words  | 21 Pagesm7 Module 7 Essay Questions 1) Describe how tooling is controlled in a part 145 maintenance organisation. Introduction Tool control within a part 145 maintenance organisation can be divided in two main areas, the control of company supplied tools and the individual control of their own personal tooling. Tool control is a part 145 requirement Safety Good tool control is essential to prevent any tooling from becoming a foreign object which might cause an obstructionRead MoreKnowing Why Airplanes Crash Is Important Essay1221 Words  | 5 Pagesmake a difference a Boeing 747-400 has over 3 million fasteners. Studies have shown the cost of carrying one extra pound on an aircraft for a year at 36,000USD in 2012 (Allain). An airline adding a crash deployable FDR module such as the â€Å"503-16 Series CPI Beacon with Memory Module†(TechTest Limited) that weighs nine pounds over a fleet of 300 aircraft would incur a fuel cost of 9.72 million USD per year. Keep in mind that with the exception of extending the life of the ULB all of these suggestedRead MoreA380 Essay11182 Words  | 45 Pagesdesigners, one from each of its partners (Aà ©rospatiale, Deutsche Aerospace AG, British Aerospace, CASA) to propose new technologies for its future aircraft designs. The designs would be presented in 1992 and the most competiti ve designs would be used.[7] In January 1993, Boeing and several companies in the Airbus consortium started a joint feasibility study of an aircraft known as the Very Large Commercial Transport (VLCT), aiming to form a partnership to share the limited market.[8][9] This jointRead MoreEASA Modul 9 questions12203 Words  | 49 PagesEASA Part 66 : Human Factor Question Module 09, Human Factors. 09.1. General. Question Number.      1.        Accidents and engineering faults are.            Option A.       insignificant and decreasing. Option B.       significant and increasing.     Option C.       insignificant and increasing.  Correct Answer is.     significant and increasing.     Explanation.   CAP 715 Ch.1 Para.2.5 CAP 716 App.G pg.2 Para 1.3.1. Question Number.      2.        Murphys law is perpetuated
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment
Note: Only a member of this blog may post a comment.